Firefly R60 Too Many Pattern Attempts done by Volcano 2.3.0

Tools:
Volcano Box (Ver 2.3.0)
Jig Cable P-07a
Install SPD android driver muna.

For safety first backup muna ang unit.
Then nag proceed nako sa format.

Quote:

Volcano Updated: 2013-09-06 Connecting... Connection successful,connected state! Version: V3.8 SN:316-772-363 Port:COM3 After format or Flash you have to press & hold power button for at least 1.30 mins. Note for win7 users : Start your Win 7 64bit with F8 key and choose 'Disable Driver Signature Enforcement'. After that the spd drivers will have the ability to be loaded. Available Ports:COM3 Detection initiated... Vcc: null Gnd: 6 7 Analyzing D+ and D-... D+ = 4, D- = 3 Analyzing USB device, please wait... Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00) Setting... Set the Pinouts failed,please reconnect and try again! Detection initiated... Vcc: null Gnd: 6 7 Analyzing D+ and D-... D+ = 4, D- = 3 Analyzing USB device, please wait... Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00) Setting... Find USB device:SPRD U2S Diag (COM7), (VID_1782&PID_4D00) Pinouts setting complete! Internal version: SPRD3 Boot downloaded. Start boot please wait a moment.... Spreadtrum Boot Block version 1.1 Boot downloaded. Flash ID: 002C00BC90555600 Flash Type:[Micron] MT29C4G48MAZAPAKD FLASH LEN:0x20000000 mtdparts=sprd-nand:256k(spl),512k(2ndbl),256k(params),512k(vmjal una),10m(modem),3840k(fixnv),3840k(backupfixnv),51 20k(dsp),3840k(runtimenv),10m(boot),10m(recovery), 150m(system),230m(userdata),60m(cache),256k(misc), 1m(boot_logo),1m(fastboot_logo),3840k(productinfo) ,512k(kpanic),512k(simlock),10m(intmemory) Analysis flash internal data successfully. Detection initiated... Vcc: null Gnd: 6 7 Analyzing D+ and D-... D+ = 4, D- = 3 Analyzing USB device, please wait... Find USB device:SPRD U2S Diag (COM7), (VID_1782&PID_4D00) Partition as follows. It isn't supported to format and ROOT the mobile phone. Unable to connect to the device, check whether the device is properly connected. Detection initiated... Vcc: null Gnd: 6 7 Analyzing D+ and D-... D+ = 4, D- = 3 Analyzing USB device, please wait... Find USB device:SPRD U2S Diag (COM7), (VID_1782&PID_4D00) Partition as follows. It isn't supported to format and ROOT the mobile phone. Unable to connect to the device, check whether the device is properly connected. Detection initiated... Vcc: null Gnd: 6 7 Analyzing D+ and D-... D+ = 4, D- = 3 Analyzing USB device, please wait... Find USB device:SPRD U2S Diag (COM7), (VID_1782&PID_4D00) Detection initiated... Vcc: null Gnd: 6 7 Analyzing D+ and D-... D+ = 4, D- = 3 Analyzing USB device, please wait... Find USB device:SPRD U2S Diag (COM7), (VID_1782&PID_4D00) Temporary does not support this operation. Ready to read/write again, please remove the power supply clip or battery and then re-loaded it. Detection initiated... Vcc: null Gnd: 6 7 Analyzing D+ and D-... D+ = 4, D- = 3 Analyzing USB device, please wait... Find USB device:SPRD U2S Diag (COM7), (VID_1782&PID_4D00) Internal version: SPRD3 Boot downloaded. Start boot please wait a moment.... Spreadtrum Boot Block version 1.1 Boot downloaded. mtdparts=sprd-nand:256k(spl),512k(2ndbl),256k(params),512k(vmjal una),10m(modem),3840k(fixnv),3840k(backupfixnv),51 20k(dsp),3840k(runtimenv),10m(boot),10m(recovery), 150m(system),230m(userdata),60m(cache),256k(misc), 1m(boot_logo),1m(fastboot_logo),3840k(productinfo) ,512k(kpanic),512k(simlock),10m(intmemory) Analysis flash internal data successfully. Set to Factory successfully. Detection initiated... Vcc: null Gnd: 6 7 Analyzing D+ and D-... D+ = 4, D- = 3 Analyzing USB device, please wait... Find USB device:SPRD U2S Diag (COM7), (VID_1782&PID_4D00) Temporary does not support this guide to read the reset function Detection initiated... Vcc: null Gnd: 6 7 Analyzing D+ and D-... D+ = 4, D- = 3 Analyzing USB device, please wait... Find USB device:SPRD U2S Diag (COM7), (VID_1782&PID_4D00) Internal version: SPRD3 Boot downloaded. Start boot please wait a moment.... Spreadtrum Boot Block version 1.1 Boot downloaded. mtdparts=sprd-nand:256k(spl),512k(2ndbl),256k(params),512k(vmjal una),10m(modem),3840k(fixnv),3840k(backupfixnv),51 20k(dsp),3840k(runtimenv),10m(boot),10m(recovery), 150m(system),230m(userdata),60m(cache),256k(misc), 1m(boot_logo),1m(fastboot_logo),3840k(productinfo) ,512k(kpanic),512k(simlock),10m(intmemory) Analysis flash internal data successfully. Set to Factory successfully. >>D:\VOLCANO BOX\VolcanoTool_v2.3.0\PrtScn\PIC_2013_09_12_10_31 _03_AM.jpg saved.