W500 SKK Password problem and now it's no power problem done

ito po dati may password at hitsura ng phone...



ipo po ginawa ko write flash with tricks...


ipo sya ng buhay na...smile na ako

 

Back up

cloudfone excite 350e hang up problem...done

cloudfone hung up
ito po sya dati
pag slide ng unlock ganyan nalang...

procedure pindutin ng marahan ang volume up
sabay power button..
ito po xa

pindutin ang volume up to select

ito na po susunod

Cherry Mobile C8 PLDT / Smart locked... unlock done

Volcano Updated: 2013-05-22
Connecting...
Connection successful,connected state!
Version: V3.8
SN:268-683-966
Port:COM5
After format or Flash you have to press & hold power button for at least 1.30 mins.
Note for win7 users :
Start your Win 7 64bit with F8 key and choose 'Disable Driver Signature Enforcement'.
After that the spd drivers will have the ability to be loaded.
Available Ports:COM3 COM4 COM5 COM110
Detection initiated...
Vcc: null
Gnd: 21 23
Analyzing D+ and D-...
D+ = 19, D- = 17
Analyzing USB device, please wait...
Find USB device:SCI USB2Serial (COM64), (VID_1782&PID_4D00)


Internal version: Spreadtrum Boot Block version 2.0
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.2
CPU TYPE:SC6610/20 [66100000]
FLASH ID: 00C8004000160000
Flash Type:[GD] GD25Q32
Size:0x400000(4MB)
Writing completed.
Flash file E:\_GSM BOX_\Volcano\Cherry Mobile\C8\MOCOR_09A_MP.W11.16_P7_Release_20130830_ 200915_*********.bin has been written.
Detection initiated...
Vcc: null
Gnd: 21 23
Analyzing D+ and D-...
D+ = 19, D- = 17
Analyzing USB device, please wait...
Find USB device:SCI USB2Serial (COM64), (VID_1782&PID_4D00)


Internal version: Spreadtrum Boot Block version 2.0
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.2
CPU TYPE:SC6610/20 [66100000]
FLASH ID: 00C8004000160000
Flash Type:[GD] GD25Q32
Size:0x400000(4MB)
Writing completed.
IMEI has been written.
Ready to read/write again, please remove the power supply clip or battery and then re-loaded it.
Detection initiated...
Vcc: null
Gnd: 21 23
Analyzing D+ and D-...
D+ = 19, D- = 17
Analyzing USB device, please wait...
Find USB device:SCI USB2Serial (COM64), (VID_1782&PID_4D00)

Internal version: Spreadtrum Boot Block version 2.0
Boot downloaded.
Start boot please wait a moment....
Spreadtrum Boot Block version 1.2
CPU TYPE:SC6610/20 [66100000]
FLASH ID: 00C8004000160000
Flash Type:[GD] GD25Q32
Size:0x400000(4MB)
>>Set to Factory successfully.1. Box settings

SPD tab
built-in boot_02
check auto pinouts (USB d+/D-)

2.use P-10c adoptor
3.write flash (use back-up file from openline C8)
4.write orig imei
5.format

Movetab MA705 (mw8850) Done!

Procedure:
1. Format SD card atleast 1 or 2 gb
2. open WM8850_Universal_Uberoid - click Changer(choose sdcard drive letter)
3. edit config folder
3. Turn off Tablet and insert SD card
4. Power on and wait for the update to finish
5. Remove SD card to reboot...Done!

Star Mobile Engage 7 inch FirmWare / FlashFile Download Now

Compatible po ito sa sa kahit anong LiveSuit Flash tool

Off the tablet

Just Press the home button

Connect cable and install drivers

you are Done

Download 

LG P698 Android Too Many Pattern Attempts!

LG P698 Android Too Many Pattern Attempts! Solved

1. Model: LG P698 Android
2. Android Version: 2.3.4
3. Problem: Too Many Pattern Attempts!

Unit Before.

Hard Reset Key Combination & right Procedure on how to Hard reset!

1. Turn the phone off,press hold the home key + volume down +
   power key for over 10 seconds then release when the LG logo appears
   then release other key when the pictures above appeared!
2. Choose Yes- Delete all user data by using home key.
3. After choosing yes by using home key then you can see logo like this see pic below.
   

Now you can hit Power on key to reset all data.

MyPhone B88i password problem done in gpg dragon

procedure:
open gpg tick check box...tapos tick mtk...put usb mode....info muna tapos run....tick read flash para
may back up tapos run...tick format...run again...tick read imei..tapos run....finish na...

ito po sya...


ITO PO PHONE...

 
ITO PO BACK UP FILES...
http://uploadmb.com/dw.php?id=1377863729&/B88i

Myphone a848i duo No Power Done.. Write flash[SOLVED]

Pero na detect pa sa PC via USB kaya ayus malamang soft brick kaya ayaw mag on .

ActionTaken:

Try Hard Reset pero no luck

Try format sa Volcano no luck din

Try Flash ayun Nadali


Procedure:

Back muna gamit ang usb cable at ang laki ng file more than 2gb




nabuhay naman kaso napansin nyo gamit kong flashfile A919 na model kaso pag pindot ng menu iba ang lumalabas


So balik lang uli tayo Volcano tapos flash nyo lang ung backup nya dati at ayun buhay parin


kaso hung lang sya sa logo so hard reset lang ang unit gamit sa pag pindot ng sabay sa volume + - at power button then wipe data


Yan suave na uli ang unit


Para sa backup :

Part1

Part2

Part3

Part4

Part5

Part6

Snap cherry mobile too many pattern attempts done via volcano box

HISTORY NAGKAROON DAW BIGLA NG TO MANY PATTERN.TRY TO HARD RESET NO LUCK..
WALA PALANG HARD RESET TO.KAYA KUHA KO SI VOLCANO...

PROCEDURE:
OPEN VOLCANO...TICK SPREADTRUM...SELECT BUILT IN BOOT_14(6820/8810)
TICK FORMAT....SELECT USB MODE....THEN HIT RUN....ANTAYIN HANGGANG MATAPOS...



ITO PO PHONE...

Samsung i9100 blank imei and phone unknown [SOLVED]

PHONE:UNKNOWN ay HW na agad o RF IC na ang sira, pwedeng subukan pang kalikutin at gawin

status upon arrival, no imei o blank imei...usually the phone has no signal

phone: unknown

open efs pro, then write good efs file

here is the result

rebuild imei in z3x, just copy the orig imei on the sticker

imei restored

phone: unknown---disappeared

Samsung a867 unlock done

Tools:
1. E210 combo cable
2. Z3x Box

Procedures of unlocking:

Qualcom mode method (only usb):

1. Power on phone.
2. Type *#197328640# -> common -> usb config -> Qualcomm mode
3. Connect USB part of 2in1 cable, setup drivers.
4. Choise qualcomm diagnostic port in port settings.
5. Choise unlock method: Read codes or Direct.
6. Press Unlock SP button.

Samsung mode method (2in1 cable):

1. Power on phone.
2. Type *#197328640# -> common -> usb config -> Samsung mode
3. Connect 2in1 cable, setup drivers.
4. Choise port of RJ45 connector in port settings
5. Choise unlock method: Read codes or Direct.
6. Press Unlock SP button.

Quote:

Selected model: A867 Selected port: COM29 Qualcomm HS-USB Diagnostics 9002 Selected port speed: 115200 Reading phone info... OK Model: SGH-A867 Country code: ¹Ì±¹/AT&T Cal date: 2008-10-24 Factory SW: UCHJ3_H Unique number: 60420000824116 Memory phone: KAV00500FM(A867) Phone S/N: R6WS279886 Reading IMEI... OK IMEI: 3558430 Build: M6290A-KPMZL-1.2.003503T Reading sysinfo... OK Calculating... OK Writing sysinfo... OK Reseting... Unlock done Done with Samsung Tool v.15.2 Done with Samsung Tool v.15.2

Zte 007z softbank also known as mf80

DC - Unlocker 2 Client 1.00.1045

Detecting modem :

selection :
manufacturer - ZTE modems
model - Auto detect (recommended)

Found modem : MF80
Model : ZTE MF80
IMEI : 357201043829434
Firmware : BD_MF80V1.0.0B18
Compile date / time : Sep 16 2011 09:02:26
Chipset : Qualcomm MDM8220
NAND Flash : HY27SF1G2A
SIM Lock status : Locked (Card Lock)

================================================== =================

Unlocking, please wait ...

Modem successfully unlocked !

Credits left :##

cherry mobile t18 INPUT PASSWORD DONE

PROBLEM
INPUT PASSWORD


TOOL
VOLCANO BOX

PROCEDURES
OPEN VOLCANO TOOL
SELECT SPD TAB(HOLD BACK KEY AND CLICK RUN)
READ INFO
READ FLASH
PHONE RESET


FINISH PRODUCT

Nokia 1280 light problem solution done

baklas ko unit at tanggal lcd, check all lines ok naman lahat.kaya naisip ko palitan yung lcd,at nagpower siya,kaya lang may problema pa walang ilaw

kaya eto ginawa ko..............

first step.........


2nd step...jumper red dot.....


finish product......

PAVIZIO X1 Too Many Pattern Attempts and No Power done in tested firmware

Model and Unit - PAVIZIO X1 Tab Android

1 Pattern or Google Accnt.
1 Black out only due to incorrect firmware








Ganda ng pagkasipat, Camera Working properly.



2 Units tested and all working



Salamat at nakadalawa agad ako sa isang Firmware


GUIDE AND TUTORIAL AND SOFTWARE here